• 24/7Service
  • QualifiedProfessionals

Lathe Machine supplier in pune

Berlin Machine provides best Lathe Machine in Pune at best cost in Pune, Mumbai, India. It is the best Lathe Machine supplier Company in Pune, Mumbai, India. The lathe is a machine tool which is used for manufacturing components that are regular about an axis. It can be used for machining cylindrical surfaces, both external and internal, and also for the turning of pointed outsides or lights. Depending on the characteristics, the following types can be distributed into several types: centre lathes or engine lathes, speed lathes, capstan lathes or turret lathes, tool room lathes, bench lathes, automatic lathes, special lathes, and CNC lathes.

Lathe Machine Manufacturer in pune

Berlin Machine is the best Lathe Machine Manufacturer Company in pune. The lathe is a very flexible and important machine to know how to operate. This machine swaps a cylindrical object against a tool that the individual controls. The lathe is the sign of all machine tools. The work is held and swapped on its axis while the cutting tool is innovative along the line of a desired cut. The lathe is one of the most multipurpose machine tools used in industry. With suitable attachments, the lather may be used for turning, tapering, form turning, screw cutting, facing, dulling, and boring, spinning, grinding, polishing operation. Cutting operations are performed with a cutting tool fed either similar or at right angles to the axis of the work. The cutting tool may also be suckled at an angle, relative to the axis of the work, for machining taper and angles. On a lathe, the tailstock does not swap. Instead, the spindle that holds the stock swaps. Collets, centres, three jaw chucks, and other work-holding attachments can all be held in rod. The tailstock can hold tools for boring, threading, reaming, or cutting tapers. Additionally, it can support the end of the work piece using a centre and can be adjusted to adapt to different work piece lengths.

Lathe machine working:

The lathe is a machine tool which grips the work piece between two rigid and strong supports called centres or in a chuck or face plate which rotates.

In a tool post which is fed against the rotating work, the cutting tool is tightly held and supported.

With the cutting tool fed either similar or at right angles to the work axis, the normal cutting operations are completed.

Description and function of lathe parts

  1. The Bed
  2. The lathe bed forms the base of the machine, the headstock and tailstock are located at also end of the bed and the posture rests over the lathe bed and slides over it.
  3. The Headstock
  4. The headstock is secured permanently on the inside ways at the left-hand end of the lathe bed.
    It includes essentially a hollow spindle and mechanism for driving and moving the spindle speed.
  5. The Tailstock
  6. The tailstock is located on the inside ways at the right-hand end of the bed.
      This has two main uses:
    • It cares the other end of the work
    • It grips a tool for performing an operation such as drilling, reaming, tapping etc.
  7. Carriage
  8. The carriage of a lathe has several parts which serve to support, move and control the cutting tool.
      Parts are following below:
    • Saddle
    • Cross-slide
    • Compound slide
    • Tool post
    • Apron
LATHE MACHINE SAFETY

As always we should be alert of protection requirements and attempt to observe safety rules in order to eliminate serious injury to ourselves or others.

Wear eyeglasses, short sleeves, no tie, no jewels, no trying to stop the work by hand. Off the main switch of machine before trying to check the work, If you don’t know how it works? –“Don’t run it.” Don’t use rags when the machine is working.

  1. Remove the key from the chuck instantly after use it. Do not start the lathe if the chuck is still in the chuck key because it is harmful.

  2. Remove the key from the chuck instantly after use it. Do not start the lathe if the chuck is still in the chuck key because it is harmful.

  3. It is important that the chuck or faceplate is securely stiffened onto the lathe’s spindle.

  4. Transfer the tool bit to a safe distance from the chuck, collet, or face plate when inserting or removing your part.

  5. Place the tool post holder to the left-hand of the compound slide. This will confirm that the compound slide will not run into the spindle or chuck parts.

  6. Place the tool post holder to the left-hand of the compound slide. This will confirm that the compound slide will not run into the spindle or chuck parts.

  7. Let confirmed first the tool bit is sharp and has correct clearance angles.

  8. Lock the tool bit as short as possible in the tool holder to prevent it from vibrating or breaking.

  9. Consistently apply and maintain cutting fluids. This will prevent transforming.

  10. Do not run a threaded spindle in reverse back.

  11. Not ever run the machine faster than the suggested speed for the specific material.

  12. If a chuck or faceplate is blocked on the spindle nose, contact an instructor to remove it.

  13. If a chuck or faceplate is blocked on the spindle nose, contact an instructor to remove it.

  14. Remember; Stop the machine before taking measurements.

  15. Stop the machine when removing long stringy chips.*

  16. Make sure that the tailstock is locked in place and that the proper adjustments are complete if the work is being turned between centres.

  17. When turning between centres, escape cutting completely through the piece.

  18. Do not use rags when the machine is working.

  19. Remove tools from the tool post and tailstock before dusting.

  20. Avoid use compressed air to clean the lathe.

Explore Our Recent Works!

Our Products


About Us

Based in Pune, Maharashtra, India, we, “Berlin Machine Corporation, established in 2008” are a widely recognized engineering house engaged in Exporting, Manufacturing, Wholesaling, and Trading of a wide gamut of Industrial Machine.

Contact Us

  • Bhairavnath Industrial Estate, Gat No.2/1, Plot No-15, Near Choudhary Weighing Bridge, Dehu-Alandi Road, Chikhali, Pune-412114
  • infoberlinmachine@gmail.com
  • +91 9923800181
  • Mon - Sat: 09:00 AM - 06:00 PM